Eastwood 180 Degree Hydraulic Aluminum and Stainless Steel Tubing Bender

Description

Looking for an easier way to bend tubing? Look no further. This Eastwood Hydraulic Tubing Bender takes all the grunt work out of tube bending and allows you to make quick, accurate repeatable bends in up to 2" x .120" wall mild steel tubing. Perfect for roll cage, suspension, and heavy tube work, this bender is easy to move and use. Roll it out of the way when you do not need it.
Features:
Make bends with high accuracy and professional results
Creates accurate, smooth, kink-free bends
Casters for mobility and easy storage. Even roll it to your project for quicker work!
1 HP motor
Build roll bars, shop fixtures, go-kart frames and much more
The Eastwood Hydraulic Tubing Bender is a high quality, precision tool capable of creating accurate, smooth, kink-free bends, up to 180 Degree in aluminum, steel and stainless steel tubing, in sizes ranging from 3/4" to 2" with available Eastwood Die Sets. Build roll bars, shop fixtures, go-kart frames and much more with high accuracy and professional results.
Easy and Accurate Fabrication.
Precision Bends in Tubing.
Fabricate Roll Bars and Race Car Components Like This Front End Frame.
Easily Roll It To Your Project. Store It When Not In Use.
Specifications
Motor Horsepower: 1
Power Requirements: 120 VAC, 60Hz, 11.5Amps
Power Cord: 8' long [2.4m], 16 Ga., Grounded
Hydraulic Fluid Type: 10W Hydraulic Fluid
Hydraulic Cylinder Bore: 63mm
Hydraulic Cylinder Stroke: 12" [0.3m]
Maximum Material Capability: 2" O.D. x 0.120" Wall Mild Steel, Aluminum (Stainless, Chromyl and other harder materials may be limited to 2" O.D. x 0.090" Wall)
Maximum Recommended Bend Angle: 90 Degree for 120 Degree Dies and 180 Degree for 240 Degree Dies (Dies NOT INCLUDED)
Contents
(1) Frame and Bender Assembly
(2) Swivel Casters
(2) Fixed Casters
(1) Degree Plate
(18) M8 x1.25 Bolts
(18) M8 Lock washers
(1) Flexible Pointer
(1) 2" Long x 7/8" U-Strap Pin
(1) 3" Long x 7/8" U-Strap Pin
(1) 4.25" Long x 7/8" Die Drive Pin
(1) 5.35" Long x 7/8" Follow Block Pin
(1) 5.5" Long x 1" Pivot Pin (installed)
NOTICE -
The following parts are included as a convenience should the Hydraulic Cylinder require future rebuilding.
Hydraulic Cylinders require specialized tools, equipment and techniques for repair.
The installed Cylinder MUST be professionally rebuilt at a local hydraulic component repair facility. DO NOT attempt self-repair.
(2) 30mm I.D. x 40mm O.D. Replacement Hydraulic Cylinder Seals
(2) 20mm I.D. x 30mm O.D. Replacement Hydraulic Cylinder Seals
(1) 55mm O.D. x 3.00mm Replacement O-Ring Seal
(1) 24mm O.D. x 3.25mm Replacement O-Ring Seal
Dies are sold separately
Available Options
21118 - 1.0" x 4" Radius, 120 Degree Die
21119 - 1.5" x 5" Radius, 120 Degree Die
21120 - 1.625" x 5" Radius, 120 Degree Die
21121 - 1.75" x 6" Radius, 120 Degree Die
21122 - 2" x 6" Radius, 120 Degree Die
21124 - 1.0" x 4" Radius, 240 Degree Die
21125 - 1.5" x 5" Radius, 240 Degree Die
21126 - 1.625" x 5" Radius, 240 Degree Die
21127 - 1.75" x 6" Radius, 240 Degree Die
Safety Information
Keep fingers and hands away from moving parts while operating this tool. Always wear proper hand, foot, and eye protection when bending tubing.